mike edwards: hi my name is mike edwards the website is home improvement doctor - part of the diy doctor group and this is the second in our series ofceramic tiling videos the first one being how to repair holes and cracks in walls with one coat, or patching plaster after you've taken the old tiles of, so having done that one we can put that stuff aside there now
i have to say apologiesfirst of all diy doctor likes to to keep things real but sometimes especially during the summer we don't book many bathrooms in we prefer to be outdoors uh... so sometimes we can't be on site but wehave built a proper film studio so that we can mock up these videos to show you - so quite clearly this isn't a real bathroom real bathroom
but we've got everything fitted so thatit will replicate the the stuff thatyou're gonna try and do your bathroom so this video is called settingout for ceramic tiles and it's a very important part of thetiling process you need to know where everysingle tile is going to go on your wall before you start and one of the things to rememberis that before you start tiling and before you choose your tiles, it's areally good idea to check just how level and flat your walls are
now you can do that simply by using a spirit level and moving that about over the walland if it's touching in most places you've got fairly flat and level walls which means that you can use biggerceramic tiles the more bumpy the walls the more undulating the smaller the tiles you will need to use or you will need to have your bathroom re-skimmed to get them flat
because if you use very big ceramic tileson a surface that is really uneven quite clearly not all of the tile isgoing to be stuck to the wall that is quite important that allof the tile is stuck to the wall okay so choose your tiles after you have checked your walls and if you've got a five hundred yearold wattle and daub cottage and the walls are all over the place likethe himalayas
and you try and stick two foot square travertine tiles on there, you're gonna have problems either skim the walls toget them flat or choose smaller tiles to go with the undulations on the wall that's the first thing the second thing is to (we are going to be tiling this wall here) the most difficult wall in the bathroom this one's got the bath on it and the toilet we've taken the toilet pan out for ease because realistically you don't actually tile around any part of the toilet pan
all you tile around is the pipe that goes into the walls andsometimes even that goes into the floor so we've taken the toilet out so you can see what we're doing so the very first thing that we need todo is to establish which is the widest part of this wall - is it the floor where the skirting board is or is it the ceiling that is the widest part of the wall
now we can do that either with a tape measure we can simply measure the bottom, themiddle and the top from side to side or we can do that in conjunctionwith the spirit level and see which way the walls are away from perpendicular in pretty much every house we've everworked in are leaning over one way or another. not necessarily by a great deal but we can simply put the spirit level on the wall
uh... and by moving the bottom or the top uh... to get it level to get it upright we can see at the bottom here there's a gap of somewhere between quarter and half an inch so that would be somewhere betweensix and ten millimeters perhaps so we know the the wall it's actually leaning over at the top
which means that the bottom is the widest part of the bathroom - so we need to check the walls both sides to make sure that's the case check it with a tape measure but once we've established the widestpart of the bathroom which in this instance is the floor we can then start to set out our tiles. first of all work out which is the widest part of the wallthat you're gonna work on
and as i've said it's the bottom in this instance, okay now the reason that we're going to do that isbecause the very last thing that we put on the wall when we're ceramic tiling are the cuts around the perimeter we cut the last tile into the wall so if it's sloping inwards, as this wall is, as we go up the cuts will get smaller
and we know we've got a neat joint all the way up, rather than starting at a wall with a full tile uh... we would be in of great deal ofdifficulty because we know the wall is sloping over at the top which means effectively the tiles if we started at that wall these tiles will be coming down at an angle
and they will look awful so we need to make sure that all of thetiles we get on this wall independently of the shape of the floor the ceiling and the walls on either side we need to know that every tile we puton there is completely square and then we can put the cuts in to suit the shape of the walls on the perimeter
and the way we're gonna do that is we are going to use a stick it's actually what is called a gauging batten and we're going gauge where our tiles go using using this baton rather than keep holding tiles onto the wall and marking them and potentially making a mistake that way we simply get a piece of timber - in this case about an inch and and an inch and a half - about thirty millimeters by ten millimeters
a piece of batten and we mark on the batten as you can see we always start with a joint in this particular case there i've done the joints in orange so they show up quite well put a tile on mark the joint move the tile over, mark the joint again and continue
all the way along the baton it doesn'tmatter in this case we've actually cut the batten off at the end of the jointso we can use it on either end but it doesn't particular matter - you'll see why later you will also notice and i will point this out to you straight away that these joints are quite a bit bigger than the 2 mm joints that tilers, domestic tilers, diy tilers home improvers tend to use the two millimeter spacer
we use five millimeter spacers simply because when the tiles are fitted absolutely square to each other on the walls then the spacers themselves, the jointsthemselves make a much better job. the joints formpart of the walls so don't try to disguise them make the the joints part of the job it's a lot neater the second reason for using slightly bigger spacers is that the most
important part of this tiling that we are going to do isn't the tiles themselves because they are waterproof to all intents and purposes - although they have got something like a three to five percent water absorption rate - they are waterproof not water-resistant, waterproof the joints however are the vulnerable part the most important part when we finish this -and that will be the final video
grouting a wall will be the getting the grout in the joints and to make thateasier, to ensure that we've got those joints watertight we open the joints upa little bit. it's a myth to think that the smaller the joints, the more watertight your wall is. that's not the case at all because sometimes that doesn't allow you to force the grout into the joint. if one little lump of grout
gets stuck in the joint, it looks likeit's full, but of course it's not. there is a void behind it so by increasing the joints a little bit and absolutely filling the joints with grout you can ensure you have got a watertight wall. okay now we're gonna set out, so we've established that the widest part of the wall is at the bottom we will start our tiling with a joint. we will put a joint against the wall. hold the stick
onto the wall - the batten onto the wall and if the cameraman can pan along there you can see that we've got joint tile joint tile etc, so we know that using this batten here that at the end of this i've put a pencil mark on the wall, which i will point to in a moment and if we started tiling along there
from that corner this would be the end of the joint of a tile. now we can see quite clearly or by measuring or holding a tile up or even using our gauge rod that leaves us with about three quartersof a tile,
that's not a bad cut to have three quarters of a tile what we don't want to end up with is tiny slivers of tile at either end or whatever but what we prefer is because this is a finished edge - or will be a finished edge by the time we've finished tiling this wall i'd prefer that three-quarters of a tile to be over on that wall
we can actually do it the other way aroundso we know that if we start with a full tile or around about a full tile going up this end nearest me we're going to end up with about threequarters of a tile at that end okay so we're going to set this wall out now thatwe've established that. we're going to set this wall out
so that we know we can start with almost a full tile here this wall itself this edge itself is sloping over exactly the same way there's going to be a little bit of cutting involved here and but it's going to look a lot neater because this is moreexposed in the corner it's going to look neater to have a bigger cut there and move the 3/4 of a tile
over to that corner and that's where we'll start tiling sothe first thing that we need to do is establish a mark on the wall, at around three-quarters of a tile - we will go back over to this corner we can say that these tiles here these are six-inch tiles, including a joint so three quarters of that
is going to be four-and-a-half inches so we can mark that on the tile which is there or we can just measure it off the wall then we can make sure we out a mark on the wall to show but that's the cut we're going to have into the corner
we know from that point onwards that's the cut tile- so after the cut tile we are going to start with a joint and then we can look across the wall and we know that the tiles will fall there we are going to look for the first vertical line that will go without any obstructions that's what we're gonna look for
and it turns out to be this one here at the end of the joint that going to be our vertical line don't forget what we're trying to do is set out a perfectly square part of this wall so that we can tile independently of what the walls either side are doing so we'll put the spirit level
on that line we know that to be perfectly upright having got the level one hundred-percent upright (i hope the camera can see that?) we can draw a line on the wall down to the skirting board so we know our first column of tiles is going to be
along this line, because we know that tobe perfectly vertical we know that if we start laying there when we lay back that way we know for a fact that we've got a three-quarter cut there and when we lay back this way we know that we have almost a full tile. there is going to be a little tile uh... little cut at the bottom and its going to get a little bit bigger - its going to be a bit bigger
at this end going into the bead that we are going to put on this wall - i have a bead here which i'll demonstrate for you. we are going to cut that tile into that bead so we have hidden the cut edge and we know that is going to be virtually a full tile there and at the same time we've got a fairly decent three-quarter cut at that side
by starting on this line. now similarly the ceiling is gonna be out of parallel very likely with the floor is not going to be level - so what we'vegot to do is do the whole thing the other way around as well. sowhat we're gonna do is put our stick, or our gauging baton on the skirting and we're gonna work up the wall again we've going to mark that there
so that we know that as a full tile and a joint at the end and then we're gonna move it up to the ceiling as close as we can get to the ceiling so by putting our gauge on the mark that i made there onlinethere we can see that if we started off at the skirting we would end up with a silly little cut
at the ceiling i hoe that makes sense? so if we started off from the skirting board with a full tile and we worked our way up we would end up with a tiny littlesliver of a cut at the ceiling which is going to look horrible, and it's going to makelife very difficult for us so the best thing to do three would be to enlarge that cut to about half a tile or three-quarters of a tile
which would of course reduce the size of the starting tile - which wouldthen go down to about three quarters of a tile so that's pretty much the same as the width and that's what we are going to achieve with the width and you will very often find that bathrooms are quite square along those lines anyway so the cuts are fairly similar so as we're going to do from side to side
we are going to do the same from the skirting here now i've cheated a little bit - i've already done this excise as i said before, if we start with around about three-quarters of a tile down at the bottom, this isn't this doesn't have to be precise uh... if we move that down a quarter of an inch all it will do is make the top a quarter of an inch bigger so we have a little bit to play with which is important when we come
to tile on the bath because now we've put this line on the wall our level line, where we're going tostart from so we can see quite clearly the intersection of these lines our first tile is going to go there and then what we need to see then is where that comes in relation to the bath
so we'll put that on there, remembering thatwe've got a joint and we can see that the top if we tile up there with full tiles, we cansee that in this instance the top of the the third tile is sixty seventy milimeters above the level of the bath. that's absolutely fine
because what we're gonna do well leave that - as we tile up the wall with our first row, we know that when we finished with the bath and we will talk about that in a moment but we know we've set out an area - a gap seventy millimeters above the bath so we mark a level line along there when we lay our third
tile and then we can set out around the bath knowing that when everything's tiled, it's all level and square and then we come back and cut those last tiles down into the bath. so that's how we set out for tiling a bathroom and ordinarily what we would do now -
everybody in the in the trade uses then, a little piece of batten and simply having marked the lines on the wall as to where the tiles are going to go we used to - and i explain that term in a moment - we simply tack that batten
to our line and that supports our first row of tile so that's our first tile that goes there we carry on tiling up the wall we cut around the pipes - which is somethingthat we will talk about later on i have another piece of batten
just here and this goes the other side of the toilet pipe so we simply fix that tap that in a couple of millimeters - it doesn't have to be a lot put that onto the line and that's where our first row of tiles goes along there and then we carry on up that line to our next course
and continue going, cutting around the cistern as we go tile cutting we will deal with in another video that's how we set out a bathroom to make sure that every tile that we put on this wall is absolutely square with the one next to it and then when we get to the edges the bottom and the top - the skirting board and the ceiling we simply cut those bits in last and we have a perfectly square wall when we have tiled up three tiles
we can then fit a batten we can cut another batten, just like this tack it to the wall at that sort of height so that our tile can carry on the along the batten and then we put the cuts in afterwards - now battens are something that have been used for years and years by tradesmen to get their first row of tiles laid out properly in the video a little later on - in fact the next in
the series - we'll be introducing erm something called tile tracker now tile tracker is an adjustable very lightweight aluminium bar which replaces the baton - it takes away the need for putting nails in the wall - takes away the need for the for the batons entirely because this simply goes against the wall and can be adjusted to the line we put on there that's a separate video altogether
that's coming that's coming on to be the next in the series that's how we set out a bathroom to make absolutely sure that regardless of the shape of the floor the walls the ceiling every tile on that wall is square to the one next to it whichgives us the perfect joints - which as i said we kept at five millimeters to make sure that we can fill it with grout
and and then we know when we come to thetiling everything's gonna be just right that's how to set out a bathroom wall for ceramic tiling and that's home improvement doctor